亚洲视频1区,国产老熟女电影久久久,无码一区毛片,欧美图片久久久久

服務熱線:
86-022-83713083
產品目錄/ PRODUCT MENU
技術支持

您現在的位置:首頁  >  技術文章  >  DIN磨耗試驗介紹

DIN磨耗試驗介紹

更新時間:2015-01-07瀏覽:10085次

DIN磨耗實驗介紹


1. 什么是磨耗實驗?     

磨耗性能是橡膠、硫化膠、熱塑性彈性體等制品的一項重要指標,與材料失效和制品的使用安全性密切相關。  

耐磨性:物理機械作用力下耐磨耗性 

相對磨損體積:橡膠試樣相對磨損體積(mm3),是指在測試之后與相同條件下與參照膠料的比較得到。 

耐磨性指數:相同條件下參照膠料體積損耗與試樣體積損耗之比,用百分?jǐn)?shù)表示  

2. 主要的測試方法    

目前比較普遍采用的三種測試方法是:國標XM一1型磨耗實驗機法(GB/T3903.2-1994)、阿克隆磨耗實驗機法(GB/T1689~1998)和DIN磨耗實驗機法(GB/T9867—1988、ISODIN ISO 4649)。*種方法用帶齒的金屬磨輪垂直壓在試樣上,以一定負荷、一定時間、一定速度,對試樣進行磨耗,測量其磨痕長度,來表示材料的耐磨性能;后兩種方法通過測定試樣在一定條件下,經機械摩擦所產生的磨耗減量,來表示材料的耐磨性能。下面主要介紹DIN磨耗實驗。 

3. DIN磨耗實驗    

該機由固定砂紙的旋轉滾筒和可水平移動的試樣夾持器組成。滾筒直徑為(150.0±0.2)mm,滾筒速度(40.0±1.0)r/min,磨耗距離為(40.0±0.2)mm,橫向前進滾筒總?cè)?shù)為84r,夾具橫向距離4.2mm/r,試樣夾具荷重2.5N,附加荷重砝碼有2.5N和5.0N兩個。試樣的直徑16mm,厚度至少6mm,試樣厚度少于6mm時,可將兩塊粘貼在一起使用。實驗時,在規定的接觸壓力(10N)下和給定面積上,采用一定規格砂紙,對試樣進行摩擦。


圖1. 磨耗測試儀示意圖Figure 1 — Schematic illustration of apparatus  圖2. 試樣制備空心鉆頭示意圖Figure 2 — Example of a hollow drill for test piece preparation  

1. Determination of abrasion resistance    

Abrasion resistance is an important index of Rubber, vulcanized orthermoplastic, and closely related with the life span and safety of materials. 

Terms and definitions 

Abrasion resistance    

The resistance to wear by mechanical action upon a surface

Relative volume loss    

The volume loss, in cubic millimetres, of the test rubber after being subjected to abrasion by an abrasive sheet which will cause a reference compound to lose a defined mass under the same specified conditions of test

Abrasion resistance index    

The ratio of the volume loss of a reference compound to the volume loss of the test rubber measured under the same specified conditions of test and expressed as a percentage

2. Main methods of determining abrasion resistance    

The standards include GB/T1689~1998, GB/T3903.2-1994,

GB/T9867—1988,ISODIN ISO 4649. The methods involve determination of the volume loss due to the abrasive action of rubbing a test piece over a specified grade of abrasive sheet. The result can be reported as a relative volume loss or an abrasion resistance index. 

3. Experiment    

The test apparatus (see Figure 1) consists of a laterally movable test piece holder and a rotatable cylinder to which the abrasive sheet (5.2) is fixed. The cylinder shall have a diameter of and a length of about and shall be rotated at a speed of , the direction of rotation being as indicated in Figure 1. The test piece holder shall have a cylindrical opening, the diameter of which can be adjusted from to and a device for adjusting the length of the test piece protruding from the opening to. The holder shall be mounted on a swivel arm that, in turn, is attached to a sledge that can be moved laterally on a spindle. The lateral displacement of the holder shall be per revolution of the drum (see note 1). Suitable attachments may be provided to rotate the test piece during the test run by rotation of the test piece holder (method B), preferably at the rate of 1 revolution per 50 revolutions of the drum.

Abrasion takes place over one of the end surfaces of the cylindrical test piece (see Figure 1). The abrasive sheet is attached to the surface of a rotating cylindrical drum against which the test piece is held and across which it is traversed. The loss in mass of the test piece is determined and the volume loss is calculated from the density of the material used for the test piece. The volume loss of the test piece is compared to that of a reference compound tested under the same conditions. 


Source:

Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device 


英語:Rubber, vulcanized or thermoplastic –Determination of abrasion resistance using a rotating cylindrical drumdevice (ISO 4649:2002)English version of DIN ISO 4649:2006-11


德語:Elastomere oder thermoplastische Elastomere –Bestimmung des Abriebwiderstandes mit einem Ger?t mit rotierender Zylindertrommel(ISO 4649:2002)Englische Fassung DIN ISO 4649:2006-11


天津尼科斯測試技術有限公司 版權所有    備案號:津ICP備13003545號-2

技術支持:化工儀器網    管理登陸    網站地圖

聯系電話:
13821512751

微信服務號

蜜乳一区二区三区四区五区六区| 我要成名最后删减了多少| 国产精品无码HEZY0| 一区二区三区无码后入内射| 2020亚洲乳码| 大鸡巴操逼吃奶| 亚洲精日韩| 亚洲午夜福利视频院| 亚洲激情图一区| 日韩图片专区欧美| 亚洲综合欧美久久精品一区二区 | 太紧了夹得我的巴好爽| 艹逼免费网站| 五月月激激网| 天天干夜夜操夜夜操夜夜摸| 综合拍一区人妻| 日本道久久专区| 欧美黄色三区四区| 欧洲日韩国产| 国产精品98福利区| 蜜臀影视一区二区三区| 蜜臀91网| 日本天天爽天天天天做| 91国产91| 日本毛片九九| 麻豆免费啊啊啊快插| 国产网爆色综合| 精品视频在线观看一区二区三区| 欧美 日韩 综合 在线| 国产亚洲精品熟女真实| 青青操在线视频精品观看| 国产嫖妓三区四区妓女| 久久午夜精品理论| 人妻日韩欧美制服综合| 天天干天天爽天天综合| 黄色影院AV| 亚洲午夜福利在线观| 久久激情久久久久久久熟女| 日本久久爱一区二区| 亚洲欧美自拍一区2区| 天天操男人天堂|